Description: DAP (Drive Acceptance Program) Documentation
Header: DAP (Drive Acceptance Program) Documentation


 This article last reviewed: 15 December, 1987

 NOTE:  The DAP (Drive Acceptance Program) is an obsolete diagnostic.  It
 has been replaced with the Apple 5.25 Inch Drive Diagnostic.  Refer to the
 Disk Drives Technical Procedures for complete information on the current
 Apple 5.25 Inch Drive Diagnostic.

 The following article describes how the DAP works and what it is designed
 to do.  For a description of how to run the DAP test or what to replace if
 a failure occurs, search on "HTS and GTS and the disk drive product name".


 TEST SEQUENCE AND DESCRIPTION

 1. WRITE PROTECT TEST (the digit 1 appears above the selected drive) -

 When the right arrow key is detected, several things happen on the screen.
 The diskette icon is erased, the drive door icon flashes to a closed
 position, and the IN.USE lamp icon lights as the first test begins.  The
 digit "1" appears above the drive to indicate the test step.

 The write protect test reads and saves a copy of sector 5 on track 16 of
 the test diskette.  This helps prevent accidental data loss if the wrong
 diskette is accidentally inserted. The write-protect test does not bother
 with the write-protect switch since this may differ in various drives and
 controllers.  Rather, it attempts to write a sector and then reads the
 sector back.  If the read detects the data pattern written, the drive is
 failed in step one.  In the case of failure (i.e. the write is successful)
 the original sector is re-written to the diskette.  If writing does occur,
 the big "X" fail sign is overlayed on the drive image.  This same
 indication is used for failure of any of the remaining tests.


 2. WRITE AND READ TEST -

 A.  SPEED (The digit 2 appears):  The first write test makes 16 D-SPEED
 passes over track 30.  The test is self-adjusting, allowing a variance of
 +- 26 WOZ counts for Apple II+, IIe and IIc systems, and +- 10 WOZ counts
 for the Apple III in emulation mode. (If the test fails at the beginning of
 the test, the drive circuitry may be unable to read/write.)

 B.  WRITE AND VERIFY TRACKS 31,32,33 (The digit 3 appears):  The write test
 writes patterns to all sectors of tracks 31,32,33 and then attempts to read
 the track.  After each read it compares the read data pattern to the pattern
 written to verify a good write and read.


 3. DYSAN DDD DISKETTE TESTS -

 A. SPIN ECCENTRICITY (spindle wobble, collet problems; displays digit 4):
 Tests tracks 21 and 24.  An even amount of error has been encoded on each of
 these DDD tracks.  A properly centered head should read each sector with
 equal ease or difficulty.  Irregularity here generally indicates collet
 problems or possibly spindle wobble.  The program allows for some errors.
 If the test shows more failures than the limit allows, the user will be
 prompted to re-insert the DDD.  On Disk II and Disk III drives it is best
 if the DDD is "double clamped".  Failure here can also indicate excess noise
 from nearby equipment or a worn DDD diskette.

 B. RADIAL ALIGNMENT (head properly centers on track; displays digit 5):
 This test reads tracks 0, 5, 16, 19, 30 and 32.  Each of these tracks has
 been encoded with errors which are progressively further from the center
 track (by one mil) with each sector.  A properly aligned drive will have a
 diminishing ability to read sectors and a perfectly positioned head will be
 unable to read the sectors furthest away from the center of the track.
 (Since the Digital Diagnostic Diskette checks alignment at six locations, it
 is possible that the error will not be detected with the Disk Alignment Aid.)

 C. HYSTERISIS (physical slope in arm motion; displays digit 6):  This test
 calibrates the drive, reads tracks 5 and 30, goes to track 34 and then reads
 tracks 30 and 5.  A properly adjusted and functioning drive will not develop
 more than +- 2 mils of error on reads when the head moves from the opposite
 direction. Errors discovered here are due to physical slop or wear in the
 hardware.  Failure of this test can often indicate that the guide rails need
 cleaning.

 D. AZIMUTH (ability of head to detect data with 21-42 minutes of error in
 the angle of data placement; displays digit 7):  This test calibrates and
 moves to track 34.  This track has been encoded with data written with
 angular error which alternates direction with each sector and increases from
 21 to 42 minutes of error. The inability to read this data indicates a faulty
 head.  In most cases all sectors are read easily by the heads in Apple drives.
 Copyright 1988 Apple Computer, Inc.
 Keywords:  hts