Path: news1.icaen!news.uiowa.edu!news.physics.uiowa.edu!newsrelay.iastate.edu!newsxfer.itd.umich.edu!newsxfer3.itd.umich.edu!howland.erols.net!cam-news-hub1.bbnplanet.com!cpk-news-hub1.bbnplanet.com!news.bbnplanet.com!news.sprintlink.net!news-peer.sprintlink.net!news1.exit109.com!hiway1.exit109.com!not-for-mail From: jruschme@hiway1.exit109.com (John Ruschmeyer) Newsgroups: comp.sys.apple2 Subject: Re: CGA/EGA/VGA monitor on IIc/IIc+ Date: 1 Mar 1997 23:35:19 -0500 Organization: Lots o' Little Piles Lines: 82 Message-ID: <5fb027$64m@hiway1.exit109.com> References: <5f83n5$eq3@hiway1.exit109.com> <5f9goo$i2b@ecom7.ecn.bgu.edu> NNTP-Posting-Host: hiway1.exit109.com In article <5f9goo$i2b@ecom7.ecn.bgu.edu>, Shawn T Beattie wrote: >jruschme@hiway1.exit109.com (John Ruschmeyer) writes: > >>In article , >>Shawn Beattie wrote: >>>I have a Sony Trinitron CPD-1302 A/D monitor. The spec sheet says it does >>>CGA/EGA/VGA/SVGA. I tried setting it to digital and using a Laser 128 to >>>CGA monitor cable to connect a //c to it, and that did not work. >>> >>>Is the Laser video pinout different from the //c? Anyone have experience >>>using this monitor on a //c (or as a VGA/SVGA monitor, by the way)? > >>Laser 128 to CGA cable? > >>If it is just a cable, then the 128 really is differnt than the //c. On the >>latter, you need what amounts to an RGB "adapter" for the video port. > >This cable I have came with my Laser 128, and I believe it could be used >to hook a CGA monitor to the Laser. This was 10 or so years ago so I may >not be remembering correctly :). I had always assumed the Laser and IIc >video ports were the same. The cable just goes 15-pin male to 9-pin >female. Well, I did a little web surfing and found out the following.... First, the Laser 128 video port pinout: Pin Signal === ====== 1 Intensity signal 2 F14M - 14 MHz 3 Red - signal 4 Blue - signal 5 Spkr sound output 6 Load Pulse for LCD 7 Dispen for LCD 8 +12 volts DC 9 Horizontal Sync Signal 10 Composite Video Sync Signal 11 Serial out - Data for LCD 12 Composite Video Output 13 Ground 14 Vertical Sync Signal 15 Green - Signal Now, the Apple //c video pinout: 1 TEXT Indicates text mode is active (special function in DHR mode) 2 14M 14 MHz clock sigal 3 SYNC Horizontal and vertical sync 4 SEGB Vertical counter signal from IOU, or lo-res indication 5 1VSOUND Sound output (one volt peak-to-peak) 6 LDPS Video shift load enable 7 WNDW Active area display blanking 8 +12V +12 volts DC 9 PRAS RAM row address strobe 10 GR Graphics mode enable 11 SEROUT Serialized character generator output 12 NTSC Composite NTSC video output 13 GND Ground reference 14 VIDD7 Bit 7 of video shift latch (for hires mode colour shifting) 15 CREF Colour reference timing signal The differences seem to be in pins 1,3,4,7(?),9,10,14,and 15. Based on the two lists it appears that while Apple provided the //c with the raw signals needed by an RGB adapter (and those needed for the LCD), the Laser was equipped with a built-in RGB converter and the appropriate pins of the connector were re-used to carry the RGB signals. My guess would be that about the only //c video accessories that might work on the 128 would be the LCD and the RF modulator. [Note to Nathan Mates, you may want to add the above to one of the FAQs. It took a lot of searching of ground to unearth it.] ------------------------------------------------------------------------ A coworker has been promising me a CGA monitor if I *really* wanted it. Maybe it's time to wire up a cable for the Laser 128. :) <<>>